詳細検索
関連検索: Bluetooth, Virtual Reality, android, mtk, smart phone, smart watch, Keyboard, OPENBOX 全てを見ます
7-Port USB 3.0 Hub With BC 1.2 Charging Port  の画像

7-Port USB 3.0 Hub With BC 1.2 Charging Port

SKU: FS997322
7-Port USB 3.0 Hub With BC 1.2 Charging Port
Reproduction is welcome and allowed for free circulation only.
     

1) smart charging
 USB smart charger intelligent control chip design. Able to identify different digital devices charging mode, charging mode and automatic conversion, full charge for the device (for example: when the iPhone is inserted charging cradle, charger smart chip generates a detection signal upon detection of the charging mode is the charging device is the Apple model *, the charger will automatically
Apple switched to charging mode for full charge. Also the use of smart charging mode to detect other devices charged and automatically adjust for optimal charging mode).
2) safe and convenient
Common USB charger USB output port and a step-down part of the design as a whole, the need to use high-voltage contact 220V power outlet, thus increasing the security risks. Especially children and the elderly, the smart charger USB output port independent, away from high voltage input current. It can be placed on a desk, coffee table, bedside daily life, etc.
Live in contact with by the middle of the place. Usually no longer need to use contact with high voltage input current completely eliminate the use of the process may occur security risks.
3) convenient
Up and the three different digital equipment charge and four USB devices for data transmission, saving more time. Multi-port design is no longer need to take more than one outlet, you save space.

USB 3.0HUB
1. Each USB port provides 900mA maximum current capable of supporting a variety of high-current device no longer requires additional power supply. (For example: mobile hard disk);
2. Support SATA interface standard. Maximum read speed of 5G second downward compatible with USB 2.0 /1.1 standards.

3. Note:
1), before use Connect the power adapter and USB smart charger and the other end into the mains socket. Open the USB smart charger switch. Power light turns on, which can charge the device.
2) Please demand charging requirements of the charging device, insert the correct USB smart charger 1A or 2A output.
3), all output ports while charging, USB Smart Charger fever is a normal phenomenon. It will not damage the equipment.
4), USB smart charger smart overcharge, overload protection monitoring chip, do not worry about long charging equipment will have an impact.
5) must not to spill liquids into USB smart charger inside, to avoid damaging the components.
6) shall not disassemble, modify, destroy USB smart charger. In order to avoid accidents.
7), the Samsung Galaxy Note tablet into this product need to slow after about 1 hour fast charge mode will turn charge charging tips marked in the case of fully depleted battery, insert the charging tip is not a normal phenomenon.
8), will not prohibit charging device into the product from the power outlet.

A PPLE Apple model is the US company's product development special charging mode, which is characterized by the use of the device in the absence of data transmission, USB interface redefining the other two pins, it also current transmission (with BC 1.2 specification DCP principle the same pattern, but each pin voltage different definitions), thereby improving the charging of speed, shorten the charging time. Defined as follows:
1A full charge mode: VCC: 5V / GND: 5V / D +: 2.0V / D-: 2.7V (applies to iPhone / iPod / iPad and other requirements in the 1A input current Apple products)
2A full charge mode: VCC: 5V / GND: 5V / D +: 2.7V / D-: 2.0V (applies to iPad / iPad mini input current requirements and other Apple products in 2A)
NOTE: For select the charge mode, in that the use of supported devices on the mode, the battery is charged with the actual power to decide how much equipment the amount of current required for charging.

BC 1.2 mode (Battery Charging Speci cation 1.2):
SDP: Standard Downstream Port downlink standard interface, which uses USB2.0 & USB3.0 specification is defined, and the charging current source: 500mA / USB2.0,900mA / USB3.0
DCP: Dedicated Charging Port dedicated charging port, this model can only be used to charge, in order to improve the charging efficiency, charging mode in the DCP, the D + / D- are shorted together will not transmit data. The company's USB smart charger only use this mode.
CDP: Charging Downstream Port charging downstream interface, the interface in this mode is a normal USB interface can be used to transmit data.
NOTE: For select the charge mode, in that the use of supported devices on the mode, the battery is charged with the actual power to decide how much equipment the amount of current required for charging.